Polymer clay benefits manufacturers - waterproof adhesive polymer clay benefits SJ-T6.doc manufacturers Tel: 15726257213 Liu polymer clay benefits ◆ Key Features: Polymer clay benefits (marble clay): dry powder, adhesive force , permeability, good water resistance, crack; good construction adaptability, can be operated in the facade and damp base surface moisture crack when used as a thin coating layer and an adhesive layer, with less process simple and fast, low cost and good quality of construction. Mainly used to gradually shaped outer walls, exterior insulation layer impermeable crack, can be used to paste tiles, mosaic tiles, marble, all kinds of stone, sand rocks and other decorative materials. ◆ Polymer clay benefits for use: one, the primary requirements:? A grassroots must be flat, firm, if the cellular defects such as cracks and should be repaired and meet the design requirements. 2.? Grassroots must be clean, construction should be preceded by cleaning the base surface of the floating dust, dirt, grease and other clean. Second, the mortar preparation: When used, in accordance with the benefits clay powder per hundred kilograms of water 25 to 30 kg were formulated, do not need any additives, artificial or mechanical stirring evenly into a thick paste. Place 5-10 minutes later, with the mix with use, mix the benefits of clay should be used within 3h, in order to avoid wasting hardened lumps. Third, the project application: for wall surface moisture, crack ???? interface layer, moisture barrier ??????? cleaning up and keep on good grass-roots moist Push Scratch a little clay benefits as waterproof mortar interface layer (thickness of about 1-2mm), drawdown should be paved and squeeze dense interfacial layer after a good scratch on its surface to be that while a clay benefits scratch proof layer before its initial setting, when the full drawdown Shop, dense, scratch proof layer and the interface layer should be directed into each other 90 °, should conserve moisture barrier after the final setting, normally that should be carried out when the moisture barrier dry surface white, lightly sprinkling showers available, one day sooner or later, the number of times, when the waterproof layer exposed curing period of not less than seven days, if it has to do to protect the surface layer, or a variety of finishes during the curing period of not less than three days. 2. adhesive for a variety of decorative tile: ?? ?????? single brick bonding layer paste: paste decorative brick, mortar clay benefits should scratch a good grass-roots level in the back face or clean up a brick adhesive layer (thickness of about 3mm), or hung by playing the line from top to bottom or bottom-ruled paste and adhesive layer to be carried out before the final setting Mifeng Mifeng with mud. ? Sided coating paste: Paste facing water requirements, we can use double-sided coating, scratch a surface that is at the grassroots-type benefits clay mortar (thickness of about 2-3mm), while in the back of a tile Scratch type benefits clay mortar (thickness of about 2-3mm) paste and adhesive layer to be carried out before the final setting Mifeng Mifeng with mud. Polymer clay polymer clay benefits one benefits, product performance: · Polymer clay benefits is the use of the polymer materials, hybrid inorganic silicate cementitious material, fine aggregate and a variety of additives, etc., through a special process of a single component, dry powder, set bond, wall interface treatment, waterproof, plugging functions in one multi-functional, high-performance, non-toxic, tasteless, new green building materials. Products meet national standards PCMW ⅠJC / T984-2005 "waterproof polymer cement mortar," the requirements, are widely used in the construction industry at home and abroad rigid waterproof wall, seepage, scraping the bottom of the paint finishes, decorative brick paste outside interface processing areas such as wall insulation system, convenient construction. · Polymer clay benefits of anti-aging, high temperature resistance, acid, odorless, harmless, green; * Polymer clay benefits water, seepage, good crack resistance. When used as a waterproof layer construction, the positive side, the back surface of the water can reach the same construction waterproof sealing effect, in the wet surface of the base construction, construction of good adaptability, can effectively solve the building wall floor slow seepage problems; · strong adhesive polymer clay benefits, can a variety of decorative tile, marble and other stone and concrete wall plate firmly bonded, and the coating is thin, with less water, paste just a step; · Polymer When the benefits of clay used as external wall insulation system interface interface treatment agent, can strengthen the combination of thermal insulation layer and the building of the base surface, the process is simple and efficient, good quality of construction. Second, the technical indicators: Item Specification Setting time initial setting / min ≥ 45 final setting / h ≤ 12 compressive strength and flexural strength 28d ≥2 4 impermeability pressure 28d ≥ 8.0 MPa 7 d ≥ 1.0 28 d ≥ 1.5 bond strength MPa 7 d ≥ 1.0 28 d ≥ 1.2 Shrinkage% 28 d ≤ 0.15 creaser 2 solution, soaking 168h without cracking ratio ≤ 3.0 alkali saturated Ca (OH), peel off the product to perform PCMW ⅠJC / T984-2005 "Polymer waterproof cement mortar "national standards. After about water = 25:10 ratio to reconcile, stirring for 15 minutes, you can be applied by brush, requiring Bohou uniform, do not miss, on the procedure to be cured: Third, use: as waterproof coating use: Press the benefits clay , then brushing the second or the third way, each about the thickness of about 1.0mm, (1.0-2.0) kg / m2; there are special requirements for certain parts, or non-woven glass fiber cloth can be enhanced using "Second, a cloth coat" process "two cloth three-coat" construction, with a thickness of about (2.0-2.5) kg / m2. For toilet, kitchen, health wall surface, waterproof outer wall boundary layer: Scratch on wet grass roots as a polymer clay benefits mortar interface layer (thickness of about 1-2 mm). Waterproof layer: Scratch interface and the interface layer immediately after a good scratch on the direction of each other in a 90 ° blade coating polymer clay benefits as mortar waterproof layer (thickness of about 2-3 mm), the requirements of paved, dense, in After the final setting waterproofing the surface white, ie watering conservation, exposed waterproof layer conservation period of not less than three days. Used as a bonding material: Press clay benefits: water ratio = 25:7.5 about reconciliation, stirring after 15 minutes can be used. For granite, marble and other decorative materials without the use of advanced drilling, construction of hanging on old technology, can like tiles, ceramic tiles and other materials, like direct smear paste, paste layer thickness should be maintained between (2.0-3.0) mm is appropriate. The same way as ordinary elements like grout paste with superior adhesion, also has a waterproof function. Used as external wall insulation system interface agent: Press clay benefits: water ratio = 25:8 about reconciliation, stirring after 15 minutes can be used. Note: Do not mixing cement, sand, stone and other materials when used. Coating dryness, recommended a fine mist water conservation. Humid air in particular, non-ventilated places, such as water tanks or basement sealing, ventilation equipment should be used to speed up the waterproof coating to dry. This product should be used at a temperature of 5 ~ 40 ℃, outdoor rain not construction. Fourth, packaging and storage: This product is 50kg / bag, should be stored in dry and ventilated place, avoid moisture, sun, rain, unopened product shelf life of 12 months.